rrTV-PHOTO   New HD TV
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 385 ONLINE 73 EVENTS SEARCH REGISTER  START HERE
 
1 page178 viewsPOST REPLY
CanoMod . A Main Hobbies . Boca Bearings

.
.
e-E-Flite Blade CP CX 400-3D > Blade 400 3D B400 swashplate problems after install HS65MG,need help.
 
 
elad400
New Heliman
Location: israel

hello,

after installing hs65mg I made some adj in swashplate mix and servo rev,
the travel of one aileron servo when play with pitch is more then the other one ,I tried to switch between the servo cables in the reciver
but still one of the servos travel too far (up & done pitch),
so I think its somting with the transmitter programing, so I learned the
manual and not found a way to adj travel of only one of the aileron servos,
need help with that,
regards
Elad.
05-07-2008 12:01 PM
 
 
whirlydude
Senior Heliman
Location: USA

It sounds to me that your setup is off. Rather than trying to explain this it would be better to watch a video of how it is done. You need to go to www.helifreak.com. Go to Finless Bob's tech talk, and then to heli skills and setup 101. You will need to login in to watch the videos, but they are very well done and informative. Go to ccpm setup part 1 & part 2. These will show you how to setup your heli. Happy Flyin!
05-07-2008 02:46 PM
 
 
elad400
New Heliman
Location: israel

It's OK now

Aux1=pitch servo not as same travel adj as the rest...
first time flying ccpm heli...


all the swashplate servos need to be at the same travel, pitch adj
only by link adj.
05-07-2008 03:11 PM
 
 
speeddemon370
Senior Heliman
Location: Spruce Grove, Alberta, Canada

http://www.rchelimag.com/pages/howto.php?howto=6&page=3

This helped me out BIGTIME. I'd probably still be grounded without it.

with 2 ears and 1 mouth you should listen twice as much as you talk
05-07-2008 09:05 PM
HOMEPAGE  
 
 
zaw
Senior Heliman
Location: Lebanon, NH - USA

Also Make sure that your swash is setup to 120*

Make sure you PIT is set to like 50% to start with. Disconnect all the linkages that are NOT connected to servos or you will bind and damage the servo during setup!. Go thought all the reversing procedures on CH 1,2 and 6. Juggle all the channels until you get it all right. it take time but you will get it.

After you get the swash plate move properly then reconnect the linkages. if they're Standard 90* servo's you should not need to adjust the travel at all. You can limit all at same time by changing pit percentage. If you limit the travel on swash servo you pit setting will be off and screw you up when you're setting up your pitch.

BCP+CP2 mix Separates BL, DD-tail, HH //\\ HBK2 JGF 400 11T //\\ Friend's B400
05-08-2008 06:12 AM
 
 
StevenT
Senior Heliman
Location: Dallas, GA USA

Was does PIT stand for? I'm going through the same problem with my 65's, but I think I've figured it out.

Steven

Shhh, don't tell the wife.
05-08-2008 06:19 AM
 
 
elad400
New Heliman
Location: israel

Thank's

I adj the links after adj the swashplate ,big improvement
now the heli fly's excellent!
05-08-2008 09:27 AM
 
 
Merlin1205
Heliman
Location: Winter haven FL

PIT=PITCH
AIL=AILERON
ELE=ELEVATOR
05-08-2008 09:40 PM
 
 
1 page178 viewsPOST REPLY
XHELI.COM . Advantage Hobby . GrandRC

.
.
e-E-Flite Blade CP CX 400-3D > Blade 400 3D B400 swashplate problems after install HS65MG,need help.
  UPDATE SCREEN   PRINT TOPIC Advertisers 

Subscribe to This Topic

Tuesday, May 13 - 10:57 am - Copyright © 2000 - 2008 runryder.com | email | link to rr | runryder needs cookie