I just ordered a flybarless 600 3d. I'm going to run it on 6s with V stabi system. what motor,servos,blades and esc. i have never owned a mikado i'm looking for suggestions.
10-24-2007 02:03 PM
Jag72 Elite Veteran Location: 20 minutes south of Boston Mass...
6S?Why did you get a logo 6003d flybarless if you plan to run 6s?
6s is designed to be run in the logo 500...the 600 3d spinning 600mm blades will require more than 6s..
I guess you could always run 550's on the 600 3d and call it a day..
Basically it all depends on what you're looking to achieve here..
Basic questions to ask:
What is your flying style? What sized blades you want to run how much power you looking for?
6s and 550's or 10s and 600's are Completely different power systems.
10-24-2007 02:23 PM
rcav8tor Heliman Location: Toledo OH USA
I guess because my Trex 600 spins 600mm blades and will do more than i'm capeable of on 6s and no flybar should be more effiant. i figured it would fly fine. i'm new to helis
10-24-2007 03:54 PM
Jag72 Elite Veteran Location: 20 minutes south of Boston Mass...
Logo 600 on 6sWell...if you decide to in fact go the 6s route I would recommend the following:
JR 8717 Servos Century 600 Plus Motor(1100KV) Jazz 80 controller A seperate 2s lipo for RX power Rotortech 560mm blades 9251/9256 tail servo ---------------
This would give you very good power
If you run 600mm blades on 6s you'llget very short run times.
10-24-2007 04:34 PM
rcman Veteran Location: Logan, Utah
Some guys are running the Actro 24-3 with 6S on the Mini Joker, which is running a 600mm main blade
David
10-25-2007 05:49 AM
BOONY Senior Heliman Location: Morecambe UK
will run fine on 6s probs more power than a trex 600 aswell. dno where u got the idea it wouldnt be any good from jag72.
Adam
Remember crashing is stupid and you could end up crying in front of your friends!
10-25-2007 08:58 PM
Jag72 Elite Veteran Location: 20 minutes south of Boston Mass...
6s logo 600 3d...Boony--I never said it wouldn't be any good...I just asked why? why would you run a killer machine like a 600 3d on 6s?
I have probably owned about 20 different logos so I have had quite a bit of experience with them
I'm no expert but I personally would never run a logo 600 3d on 6s? I'm sure even on 6s it would outfly a trex 600 but that is besides the point.
If you are looking for a 6s machine you typically go with a logo 500 running 500-550's...NOT a logo 600 3d running 600's
The real issue here is amp draw and flight times..running 6s on a logo 600 would require a fat as$ pack and you'd get a very short run time...if you take that same heli and go with a 10s setup you'd get more power and longer flight times...Like I said before...it's personal preference and also what you are looking to achieve
6s is "Okay" at best...but 10s is "Insane"
I myself have decided to go the 10s route with my logo 600 3d
10-26-2007 03:22 PM
BOONY Senior Heliman Location: Morecambe UK
gotta agree 10s will be killer
but 6s is pretty good too
Adam
Remember crashing is stupid and you could end up crying in front of your friends!
-8471.jpg){kind=logo}
