rrTV-PHOTO   New HD TV
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 785 ONLINE 19 EVENTS SEARCH REGISTER  START HERE
 
1 page349 viewsPOST REPLY
CanoMod . Futaba-RC . A Main Hobbies

.
.
Align T-REX 600N 700N > One Way Press Fit
 
 
ringram2077
Senior Heliman
Location: Birmingham, AL

When pressing in a new one way is any kind of retainer (loktite, etc.)required ?
08-02-2007 Over year old.
HOMEPAGE  
 
 
JMF
Senior Heliman
Location: Clinton

One gentleman was saying to use a touch of loctite because his bearing spun inside the hub without it.
Hope I helped.
Look at the "one way issue count" I seen it in there somewheres.
08-02-2007 Over year old.
 
 
ringram2077
Senior Heliman
Location: Birmingham, AL

Yep, it will need some retainer. You can push the new one way back in by hand. I am using some of the green that came with the kit. Hope it holds. I also cleaned out the new one way and plan to try the white lithium grease. Will see how it works tomorrow.
08-02-2007 Over year old.
HOMEPAGE  
 
 
helibird
Key Veteran
Location: St. George, UT

Yes locktite it in. I had mine spin in the hub, sucked cause I thought it was the clutch slipping and I dropped the engine to check.
08-02-2007 Over year old.
 
 
j5coat
Veteran
Location: Phoenix

mine did not press in by hand, it was in fact very tight. I did not use any loctite on it and it has been fine. But just to be safe use a dab of green once you get it in place, that should hold it great.

Trex 700, Trex 600n
08-02-2007 Over year old.
 
 
helibird
Key Veteran
Location: St. George, UT

Mine didn't press in by hand either but it spun after a couple flights.
08-06-2007 Over year old.
 
 
LJS
Veteran
Location: Minnesota, USA

I just replaced my autorotation bearing. It pressed in so easily that I'm concerned it might not hold even with loctite. I've got four flights on it and so far, so good.

Keep 'em flying.

LJS

600E, 1910 1Y, 8S FP4270, GY611
600N, OS50 Hyper, GY611
Logo 5003D, 600+, 6S TP 5000, DS760
08-06-2007 Over year old.
 
 
ringram2077
Senior Heliman
Location: Birmingham, AL

After some green loktite I shot some thin CA in for insurance. It is holding fine even though the new one way is still locking.
08-07-2007 Over year old.
HOMEPAGE  
 
 
JMF
Senior Heliman
Location: Clinton

what brand of new one way are you using?
08-07-2007 Over year old.
 
 
ringram2077
Senior Heliman
Location: Birmingham, AL

So far I am using the same type that came with the kit. Align is suppose to have a new one available soon (HN6064). The one I just replaced also locks up, just not as tight. I used the white lithium. I may try once more with triflo or atf and see if that is any better.
08-07-2007 Over year old.
HOMEPAGE  
 
 
1 page349 viewsPOST REPLY
Boca Bearings . Modefo's RC Helicopters . XHELI.COM

.
.
Align T-REX 600N 700N > One Way Press Fit
 PRINT TOPIC Advertisers 

Subscribe to This Topic

Monday, December 1 - 11:54 pm - Copyright © 2000 - 2008 runryder.com | email | link to rr | runryder needs cookie