Is it possible to use HoneyBee king main blade on honeybee cp2....
04-10-2006 Over year old.
Martin_gsxr Veteran Location: Montreal, Canada
Hi fx20v,
No it is not possible because the main blades will touch the tail blades...
King Blade = 10.750 inch or 273mm
04-10-2006 Over year old.
t.edwards Senior Heliman Location: Lake Geneva, Wisconsin
Longer boom, more motor....
04-10-2006 Over year old.
fx20v Heliman Location: Malaysia
Hi,
It's seems cp2 and honeybee king almost same size.Hmm..maybe the tail boom abit longer..
04-10-2006 Over year old.
Martin_gsxr Veteran Location: Montreal, Canada
Hi fx20v, No same size 520mm long, but the King main blade are 1 inch higher on the head..
04-10-2006 Over year old.
fx20v Heliman Location: Malaysia
Hi Martin_gsxr,
Yeah, so it's same size with cp2 but the king rotorhead higher than cp2 rotorhead so do the main blade.
Do you think possible or not if i using DD motor with small prop so the main blade won't hit the tail rotor....
04-10-2006 Over year old.
Martin_gsxr Veteran Location: Montreal, Canada
fx20v, yes you could with DD... with a 4inch diameter prop. they are just barely touching.. a GWS EP-3020 will be just fine .
04-10-2006 Over year old.
t.edwards Senior Heliman Location: Lake Geneva, Wisconsin
When you said the blades are 273mm was that from the grip bolt to the tip? Tom
04-10-2006 Over year old.
Martin_gsxr Veteran Location: Montreal, Canada
Tom, 263mm from the bolt grip to the tip or 273mm from tip to tip...
04-10-2006 Over year old.
fx20v Heliman Location: Malaysia
Hi,
With longer main blade will it make the whole heli stable in hovering..
04-10-2006 Over year old.
Martin_gsxr Veteran Location: Montreal, Canada
Yes for sure, but it will pull more amp of your ESC..
That why I maybe buy a CC25, now I am with the CC10.
04-10-2006 Over year old.
fx20v Heliman Location: Malaysia
Martin_gsxr,
I'm currently using brushless motor so i'm not worried the 4in1 mixer burnout.The only thing i concern the king main blade maybe won't fit into cp2 blade grip holder....
04-10-2006 Over year old.
Martin_gsxr Veteran Location: Montreal, Canada
FX20V, they have about 1mm difference..
The bolt n the King is bigger too, so maybe you could put the plastic end of Cp2 blades to King`s blade to reduce the hole..
04-10-2006 Over year old.
fx20v Heliman Location: Malaysia
Martin_gsxr,
Thanks for the information ,I will try it later.........
04-10-2006 Over year old.
t.edwards Senior Heliman Location: Lake Geneva, Wisconsin
The King blades are 5mm thick at the blade grip?
04-10-2006 Over year old.
Martin_gsxr Veteran Location: Montreal, Canada
Tom, the inside of the King grip is 7mm
04-10-2006 Over year old.
fx20v Heliman Location: Malaysia
Hi..,
I tested the king blade on cp2 and whole cp2 much more stable.It's also tracking much better than cp2 main blade.I always got this problem tracking the cp2 main blade.Too bad it's hit the tail rotor if i pull down the elevator too much.
04-12-2006 Over year old.
fx20v Heliman Location: Malaysia
Hi,
I shorten the honeybee king main blade to avoid hitting the tail rotor.The King blade now is just longer than stock cp2 by 11mm.It's hover pretty stable.I got tail boom strike cause by hard landing and suprisingly the king blade show no sign of damage and crack.
